isapnp.conf

Isapnp (isapnp.conf)

luizhacker

Habilitar SoundBlaster 16 AWE

Categoria: Hardware

Software: Isapnp

[ Hits: 4.978 ]

Por: Lorran Luiz

0 0

Denuncie Favoritos Indicar
Este arquivo demonstra com habilitar sua placa de som Plug and Play off-board que usa o barramento ISA. No arquivo a placa mãe que está sendo configurada é uma Sound Blaster 16 AWE fabricada pela Creative.

O arquivo pode ser salvo no diretório /etc, e deve ser usado no programa de configuração de hardware isapnp da seguinte maneira:

# isapnp /etc/isapnp.conf

Existem algumas opções de configuração no próprio arquivo, e você poderá ecolher a de sua preferência descomentando-as e comentando as configurações atuais.

A porta de game encontra-se desativada nesse arquivo pois haverá um conflito durante a alocação de memória no seu endereço. Esse conflito ocorre porque a controladora de joystick já é automáticamente habilitada no sistema (pelo menos no meu caso).
# $Id: pnpdump_main.c,v 1.27 2001/04/30 21:54:53 fox Exp $
# Release isapnptools-1.26
# 
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
# 
# For details of the output file format, see isapnp.conf(5)
# 
# For latest information and FAQ on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
# 
# Compiler flags:  -DREALTIME -DHAVE_PROC -DENABLE_PCI -DHAVE_SCHED_SETSCHEDULER -DHAVE_NANOSLEEP -DWANT_TO_VALIDATE
# 
# Trying port address 0273
# Board 1 has serial identifier 84 1b 04 d8 ee 9c 00 8c 0e

# (DEBUG)
(READPORT 0x0273)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING

# Card 1: (serial identifier 84 1b 04 d8 ee 9c 00 8c 0e)
# Vendor Id CTL009c, Serial Number 453302510, checksum 0x84.
# Version 1.0, Vendor version 1.2
# ANSI string -->Creative SB32 PnP<--
#
# Logical device id CTL0041
#     Device supports vendor reserved register @ 0x38
#     Device supports vendor reserved register @ 0x3a
#     Device supports vendor reserved register @ 0x3c
#     Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL009c/453302510 (LD 0
#     ANSI string -->Audio<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       IRQ 5.
#             High true, edge sensitive interrupt (by default)
(INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 1.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
(DMA 0 (CHANNEL 1))
#       Next DMA channel 5.
#             16 bit DMA only
#             Logical device is a bus master
#             DMA may not execute in count by byte mode
#             DMA may execute in count by word mode
#             DMA channel speed in compatible mode
(DMA 1 (CHANNEL 5))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0220
#             IO base alignment 1 bytes
#             Number of IO addresses required: 16
(IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0330
#             Maximum IO base address 0x0330
#             IO base alignment 1 bytes
#             Number of IO addresses required: 2
(IO 1 (SIZE 2) (BASE 0x0330))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0388
#             IO base alignment 1 bytes
#             Number of IO addresses required: 4
(IO 2 (SIZE 4) (BASE 0x0388))

#       Start dependent functions: priority acceptable
#       IRQ 5, 7, 9 or 10.
#             High true, edge sensitive interrupt (by default)
#(INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
#(DMA 0 (CHANNEL 0))
#       Next DMA channel 5, 6 or 7.
#             16 bit DMA only
#             Logical device is a bus master
#             DMA may not execute in count by byte mode
#             DMA may execute in count by word mode
#             DMA channel speed in compatible mode
#(DMA 1 (CHANNEL 5))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
#(IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0330
#             IO base alignment 48 bytes
#             Number of IO addresses required: 2
#(IO 1 (SIZE 2) (BASE 0x0300))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0388
#             IO base alignment 1 bytes
#             Number of IO addresses required: 4
#(IO 2 (SIZE 4) (BASE 0x0388))

#       Start dependent functions: priority acceptable
#       IRQ 5, 7, 9 or 10.
#             High true, edge sensitive interrupt (by default)
#(INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
#(DMA 0 (CHANNEL 0))
#       Next DMA channel 5, 6 or 7.
#             16 bit DMA only
#             Logical device is not a bus master
#             DMA may not execute in count by byte mode
#             DMA may execute in count by word mode
#             DMA channel speed in compatible mode
#(DMA 1 (CHANNEL 5))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
#(IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0330
#             IO base alignment 48 bytes
#             Number of IO addresses required: 2
#(IO 1 (SIZE 2) (BASE 0x0300))

#       Start dependent functions: priority acceptable
#       IRQ 5, 7, 9 or 10.
#             High true, edge sensitive interrupt (by default)
#(INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
#(DMA 0 (CHANNEL 0))
#       Next DMA channel 5, 6 or 7.
#             16 bit DMA only
#             Logical device is a bus master
#             DMA may not execute in count by byte mode
#             DMA may execute in count by word mode
#             DMA channel speed in compatible mode
#(DMA 1 (CHANNEL 5))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
#(IO 0 (SIZE 16) (BASE 0x0220))

#       Start dependent functions: priority acceptable
#       IRQ 5, 7, 9 or 10.
#             High true, edge sensitive interrupt (by default)
#(INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
#(DMA 0 (CHANNEL 0))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
#(IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0330
#             IO base alignment 48 bytes
#             Number of IO addresses required: 2
#(IO 1 (SIZE 2) (BASE 0x0300))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0388
#             IO base alignment 1 bytes
#             Number of IO addresses required: 4
#(IO 2 (SIZE 4) (BASE 0x0388))

#       Start dependent functions: priority acceptable
#       IRQ 5, 7, 9 or 10.
#             High true, edge sensitive interrupt (by default)
#(INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
#(DMA 0 (CHANNEL 0))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
#(IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0330
#             IO base alignment 48 bytes
#             Number of IO addresses required: 2
#(IO 1 (SIZE 2) (BASE 0x0300))

#       Start dependent functions: priority acceptable
#       IRQ 5, 7, 9 or 10.
#             High true, edge sensitive interrupt (by default)
#(INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
#(DMA 0 (CHANNEL 0))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
#(IO 0 (SIZE 16) (BASE 0x0220))

#       Start dependent functions: priority functional
#       IRQ 5, 7, 9 or 10.
#             High true, edge sensitive interrupt (by default)
#(INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
#(DMA 0 (CHANNEL 0))
#       Next DMA channel 5, 6 or 7.
#             16 bit DMA only
#             Logical device is a bus master
#             DMA may not execute in count by byte mode
#             DMA may execute in count by word mode
#             DMA channel speed in compatible mode
#(DMA 1 (CHANNEL 5))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
#(IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0330
#             IO base alignment 16 bytes
#             Number of IO addresses required: 2
#(IO 1 (SIZE 2) (BASE 0x0300))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0394
#             IO base alignment 4 bytes
#             Number of IO addresses required: 4
#(IO 2 (SIZE 4) (BASE 0x0388))

#     End dependent functions
 (NAME "CTL009c/453302510[0]{Audio               }")
(ACT Y)
))
#
# Logical device id CTL7002
#     Device supports vendor reserved register @ 0x39
#     Device supports vendor reserved register @ 0x3a
#     Device supports vendor reserved register @ 0x3c
#     Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL009c/453302510 (LD 1
#     ANSI string -->Game<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0200
#             Maximum IO base address 0x0200
#             IO base alignment 1 bytes
#             Number of IO addresses required: 8
#(IO 0 (SIZE 8) (BASE 0x0200))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0200
#             Maximum IO base address 0x0208
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
#(IO 0 (SIZE 8) (BASE 0x0201))

#     End dependent functions
 (NAME "CTL009c/453302510[1]{Game                }")
#(ACT Y)
))
#
# Logical device id CTL0021
#     Device supports vendor reserved register @ 0x38
#     Device supports vendor reserved register @ 0x3a
#     Device supports vendor reserved register @ 0x3c
#     Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL009c/453302510 (LD 2
#     ANSI string -->WaveTable<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0620
#             Maximum IO base address 0x0620
#             IO base alignment 1 bytes
#             Number of IO addresses required: 4
(IO 0 (SIZE 4) (BASE 0x0620))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0620
#             Maximum IO base address 0x0680
#             IO base alignment 32 bytes
#             Number of IO addresses required: 4
#(IO 0 (SIZE 4) (BASE 0x0620))

#     End dependent functions
 (NAME "CTL009c/453302510[2]{WaveTable           }")
(ACT Y)
))
#
# Logical device id CTL2011
#     Device supports vendor reserved register @ 0x38
#     Device supports vendor reserved register @ 0x3a
#     Device supports vendor reserved register @ 0x3c
#     Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL009c/453302510 (LD 3
#     Compatible device id PNP0600
#     ANSI string -->IDE<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       IRQ 10.
#             High true, edge sensitive interrupt (by default)
(INT 0 (IRQ 10 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0168
#             Maximum IO base address 0x0168
#             IO base alignment 1 bytes
#             Number of IO addresses required: 8
(IO 0 (SIZE 8) (BASE 0x0168))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x036e
#             Maximum IO base address 0x036e
#             IO base alignment 1 bytes
#             Number of IO addresses required: 2
(IO 1 (SIZE 2) (BASE 0x036e))

#       Start dependent functions: priority acceptable
#       IRQ 11.
#             High true, edge sensitive interrupt (by default)
#(INT 0 (IRQ 11 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x01e8
#             Maximum IO base address 0x01e8
#             IO base alignment 1 bytes
#             Number of IO addresses required: 8
#(IO 0 (SIZE 8) (BASE 0x01e8))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x03ee
#             Maximum IO base address 0x03ee
#             IO base alignment 1 bytes
#             Number of IO addresses required: 2
#(IO 1 (SIZE 2) (BASE 0x03ee))

#       Start dependent functions: priority acceptable
#       IRQ 10, 11, 12 or 15.
#             High true, edge sensitive interrupt (by default)
#(INT 0 (IRQ 10 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0180
#             Maximum IO base address 0x01b8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
#(IO 0 (SIZE 8) (BASE 0x0180))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0306
#             Maximum IO base address 0x033e
#             IO base alignment 8 bytes
#             Number of IO addresses required: 2
#(IO 1 (SIZE 2) (BASE 0x0306))

#       Start dependent functions: priority functional
#       IRQ 15.
#             High true, edge sensitive interrupt (by default)
#(INT 0 (IRQ 15 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0170
#             Maximum IO base address 0x0170
#             IO base alignment 1 bytes
#             Number of IO addresses required: 8
#(IO 0 (SIZE 8) (BASE 0x0170))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0376
#             Maximum IO base address 0x0376
#             IO base alignment 1 bytes
#             Number of IO addresses required: 1
#(IO 1 (SIZE 1) (BASE 0x0376))

#     End dependent functions
 (NAME "CTL009c/453302510[3]{IDE                 }")
(ACT Y)
))
# End tag... Checksum 0x00 (OK)

# Returns all cards to the "Wait for Key" state
(WAITFORKEY)
Comentários
Nenhum comentário foi encontrado.