gustavo_henrique
(usa Ubuntu)
Enviado em 08/03/2012 - 14:31h
# WELCOME TO SQUID 2.6.STABLE21
# ----------------------------s
#
# This is the default Squid configuration file. You may wish
# to look at the Squid home page (http://www.squid-cache.org/)
# for the FAQ and other documentation.
#
# The default Squid config file shows what the defaults for
# various options happen to be. If you don't need to change the
# default, you shouldn't uncomment the line. Doing so may cause
# run-time problems. In some cases "none" refers to no default
# setting at all, while in other cases it refers to a valid
# option - the comments for that keyword indicate if this is the
# case.
#
# OPTIONS FOR AUTHENTICATION
# -----------------------------------------------------------------------------
# TAG: auth_param
# This is used to define parameters for the various authentication
# schemes supported by Squid.
#
# format: auth_param scheme parameter [setting]
#
# The order in which authentication schemes are presented to the client is
# dependent on the order the scheme first appears in config file. IE
# has a bug (it's not RFC 2617 compliant) in that it will use the basic
# scheme if basic is the first entry presented, even if more secure
# schemes are presented. For now use the order in the recommended
# settings section below. If other browsers have difficulties (don't
# recognize the schemes offered even if you are using basic) either
# put basic first, or disable the other schemes (by commenting out their
# program entry).
#
# Once an authentication scheme is fully configured, it can only be
# shutdown by shutting squid down and restarting. Changes can be made on
# the fly and activated with a reconfigure. I.E. You can change to a
# different helper, but not unconfigure the helper completely.
#
# Please note that while this directive defines how Squid processes
# authentication it does not automatically activate authentication.
# To use authentication you must in addition make use of ACLs based
# on login name in http_access (proxy_auth, proxy_auth_regex or
# external with %LOGIN used in the format tag). The browser will be
# challenged for authentication on the first such acl encountered
# in http_access processing and will also be re-challenged for new
# login credentials if the request is being denied by a proxy_auth
# type acl.
#
# WARNING: authentication can't be used in a transparently intercepting
# proxy as the client then thinks it is talking to an origin server and
# not the proxy. This is a limitation of bending the TCP/IP protocol to
# transparently intercepting port 80, not a limitation in Squid.
#
# === Parameters for the basic scheme follow. ===
#
# "program" cmdline
# Specify the command for the external authenticator. Such a program
# reads a line containing "username password" and replies "OK" or
# "ERR" in an endless loop. "ERR" responses may optionally be followed
# by a error description available as %m in the returned error page.
#
# By default, the basic authentication scheme is not used unless a
# program is specified.
#
# If you want to use the traditional proxy authentication, jump over to
# the helpers/basic_auth/NCSA directory and type:
# % make
# % make install
#
# Then, set this line to something like
#
# auth_param basic program /usr/libexec/ncsa_auth /usr/etc/passwd
#
# "children" numberofchildren
# The number of authenticator processes to spawn. If you start too few
# squid will have to wait for them to process a backlog of credential
# verifications, slowing it down. When credential verifications are
# done via a (slow) network you are likely to need lots of
# authenticator processes.
# auth_param basic children 5
#
# "concurrency" numberofconcurrentrequests
# The number of concurrent requests/channels the helper supports.
# Changes the protocol used to include a channel number first on
# the request/response line, allowing multiple requests to be sent
# to the same helper in parallell without wating for the response.
# Must not be set unless it's known the helper supports this.
#
# "realm" realmstring
# Specifies the realm name which is to be reported to the client for
# the basic proxy authentication scheme (part of the text the user
# will see when prompted their username and password).
# auth_param basic realm Squid proxy-caching web server
#
# "credentialsttl" timetolive
# Specifies how long squid assumes an externally validated
# username:password pair is valid for - in other words how often the
# helper program is called for that user. Set this low to force
# revalidation with short lived passwords. Note that setting this high
# does not impact your susceptibility to replay attacks unless you are
# using an one-time password system (such as SecureID). If you are using
# such a system, you will be vulnerable to replay attacks unless you
# also use the max_user_ip ACL in an http_access rule.
# auth_param basic credentialsttl 2 hours
#
# "casesensitive" on|off
# Specifies if usernames are case sensitive. Most user databases are
# case insensitive allowing the same username to be spelled using both
# lower and upper case letters, but some are case sensitive. This
# makes a big difference for user_max_ip ACL processing and similar.
# auth_param basic casesensitive off
#
# "blankpassword" on|off
# Specifies if blank passwords should be supported. Defaults to off
# as there is multiple authentication backends which handles blank
# passwords as "guest" access.
#
# === Parameters for the digest scheme follow ===
#
# "program" cmdline
# Specify the command for the external authenticator. Such a program
# reads a line containing "username":"realm" and replies with the
# appropriate H(A1) value hex encoded or ERR if the user (or his H(A1)
# hash) does not exists. See RFC 2616 for the definition of H(A1).
# "ERR" responses may optionally be followed by a error description
# available as %m in the returned error page.
#
# By default, the digest authentication scheme is not used unless a
# program is specified.
#
# If you want to use a digest authenticator, jump over to the
# helpers/digest_auth/ directory and choose the authenticator to use.
# It it's directory type
# % make
# % make install
#
# Then, set this line to something like
#
# auth_param digest program /usr/libexec/digest_auth_pw /usr/etc/digpass
#
# "children" numberofchildren
# The number of authenticator processes to spawn. If you start too few
# squid will have to wait for them to process a backlog of credential
# verifications, slowing it down. When credential verifications are
# done via a (slow) network you are likely to need lots of
# authenticator processes.
# auth_param digest children 5
#
# "concurrency" numberofconcurrentrequests
# The number of concurrent requests/channels the helper supports.
# Changes the protocol used to include a channel number first on
# the request/response line, allowing multiple requests to be sent
# to the same helper in parallell without wating for the response.
# Must not be set unless it's known the helper supports this.
#
# "realm" realmstring
# Specifies the realm name which is to be reported to the client for the
# digest proxy authentication scheme (part of the text the user will see
# when prompted their username and password).
# auth_param digest realm Squid proxy-caching web server
#
# "nonce_garbage_interval" timeinterval
# Specifies the interval that nonces that have been issued to clients are
# checked for validity.
# auth_param digest nonce_garbage_interval 5 minutes
#
# "nonce_max_duration" timeinterval
# Specifies the maximum length of time a given nonce will be valid for.
# auth_param digest nonce_max_duration 30 minutes
#
# "nonce_max_count" number
# Specifies the maximum number of times a given nonce can be used.
# auth_param digest nonce_max_count 50
#
# "nonce_strictness" on|off
# Determines if squid requires strict increment-by-1 behavior for nonce
# counts, or just incrementing (off - for use when useragents generate
# nonce counts that occasionally miss 1 (ie, 1,2,4,6)).
# auth_param digest nonce_strictness off
#
# "check_nonce_count" on|off
# This directive if set to off can disable the nonce count check
# completely to work around buggy digest qop implementations in certain
# mainstream browser versions. Default on to check the nonce count to
# protect from authentication replay attacks.
# auth_param digest check_nonce_count on
#
# "post_workaround" on|off
# This is a workaround to certain buggy browsers who sends an incorrect
# request digest in POST requests when reusing the same nonce as acquired
# earlier in response to a GET request.
# auth_param digest post_workaround off
#
# === NTLM scheme options follow ===
#
# "program" cmdline
# Specify the command for the external NTLM authenticator. Such a
# program participates in the NTLMSSP exchanges between Squid and the
# client and reads commands according to the Squid NTLMSSP helper
# protocol. See helpers/ntlm_auth/ for details. Recommended ntlm
# authenticator is ntlm_auth from Samba-3.X, but a number of other
# ntlm authenticators is available.
#
# By default, the ntlm authentication scheme is not used unless a
# program is specified.
#
# auth_param ntlm program /path/to/samba/bin/ntlm_auth --helper-protocol=squid-2.5-ntlmssp
#
# "children" numberofchildren
# The number of authenticator processes to spawn. If you start too few
# squid will have to wait for them to process a backlog of credential
# verifications, slowing it down. When credential verifications are
# done via a (slow) network you are likely to need lots of
# authenticator processes.
# auth_param ntlm children 5
#
# "keep_alive" on|off
# This option enables the use of keep-alive on the initial
# authentication request. It has been reported some versions of MSIE
# have problems if this is enabled, but performance will be increased
# if enabled.
#
# auth_param ntlm keep_alive on
#
# === Negotiate scheme options follow ===
#
# "program" cmdline
# Specify the command for the external Negotiate authenticator. Such a
# program participates in the SPNEGO exchanges between Squid and the
# client and reads commands according to the Squid ntlmssp helper
# protocol. See helpers/ntlm_auth/ for details. Recommended SPNEGO
# authenticator is ntlm_auth from Samba-4.X.
#
# By default, the Negotiate authentication scheme is not used unless a
# program is specified.
#
# auth_param negotiate program /path/to/samba/bin/ntlm_auth --helper-protocol=gss-spnego
#
# "children" numberofchildren
# The number of authenticator processes to spawn. If you start too few
# squid will have to wait for them to process a backlog of credential
# verifications, slowing it down. When credential verifications are
# done via a (slow) network you are likely to need lots of
# authenticator processes.
# auth_param negotiate children 5
#
# "keep_alive" on|off
# If you experience problems with PUT/POST requests when using the
# Negotiate authentication scheme then you can try setting this to
# off. This will cause Squid to forcibly close the connection on
# the initial requests where the browser asks which schemes are
# supported by the proxy.
#
# auth_param negotiate keep_alive on
#
#Recommended minimum configuration per scheme:
#auth_param negotiate program <uncomment and complete this line to activate>
#auth_param negotiate children 5
#auth_param negotiate keep_alive on
#auth_param ntlm program <uncomment and complete this line to activate>
#auth_param ntlm children 5
#auth_param ntlm keep_alive on
#auth_param digest program <uncomment and complete this line>
#auth_param digest children 5
#auth_param digest realm Squid proxy-caching web server
#auth_param digest nonce_garbage_interval 5 minutes
#auth_param digest nonce_max_duration 30 minutes
#auth_param digest nonce_max_count 50
#auth_param basic program <uncomment and complete this line>
#auth_param basic children 5
#auth_param basic realm Squid proxy-caching web server
#auth_param basic credentialsttl 2 hours
#auth_param basic casesensitive off
# TAG: authenticate_cache_garbage_interval
# The time period between garbage collection across the username cache.
# This is a tradeoff between memory utilization (long intervals - say
# 2 days) and CPU (short intervals - say 1 minute). Only change if you
# have good reason to.
#
#Default:
# authenticate_cache_garbage_interval 1 hour
# TAG: authenticate_ttl
# The time a user & their credentials stay in the logged in user cache
# since their last request. When the garbage interval passes, all user
# credentials that have passed their TTL are removed from memory.
#
#Default:
# authenticate_ttl 1 hour
# TAG: authenticate_ip_ttl
# If you use proxy authentication and the 'max_user_ip' ACL, this
# directive controls how long Squid remembers the IP addresses
# associated with each user. Use a small value (e.g., 60 seconds) if
# your users might change addresses quickly, as is the case with
# dialups. You might be safe using a larger value (e.g., 2 hours) in a
# corporate LAN environment with relatively static address assignments.
#
#Default:
# authenticate_ip_ttl 0 seconds
# ACCESS CONTROLS
# -----------------------------------------------------------------------------
# TAG: external_acl_type
# This option defines external acl classes using a helper program to
# look up the status
#
# external_acl_type name [options] FORMAT.. /path/to/helper [helper arguments..]
#
# Options:
#
# ttl=n TTL in seconds for cached results (defaults to 3600
# for 1 hour)
# negative_ttl=n
# TTL for cached negative lookups (default same
# as ttl)
# children=n number of processes spawn to service external acl
# lookups of this type. (default 5).
# concurrency=n concurrency level per process. Only used with helpers
# capable of processing more than one query at a time.
# Note: see compatibility note below
# cache=n result cache size, 0 is unbounded (default)
# grace= Percentage remaining of TTL where a refresh of a
# cached entry should be initiated without needing to
# wait for a new reply. (default 0 for no grace period)
# protocol=2.5 Compatibility mode for Squid-2.5 external acl helpers
#
# FORMAT specifications
#
# %LOGIN Authenticated user login name
# %EXT_USER Username from external acl
# %IDENT Ident user name
# %SRC Client IP
# %SRCPORT Client source port
# %DST Requested host
# %PROTO Requested protocol
# %PORT Requested port
# %METHOD Request method
# %MYADDR Squid interface address
# %MYPORT Squid http_port number
# %PATH Requested URL-path (including query-string if any)
# %USER_CERT SSL User certificate in PEM format
# %USER_CERTCHAIN SSL User certificate chain in PEM format
# %USER_CERT_xx SSL User certificate subject attribute xx
# %USER_CA_xx SSL User certificate issuer attribute xx
# %{Header} HTTP request header
# %{Hdr:member} HTTP request header list member
# %{Hdr:;member}
# HTTP request header list member using ; as
# list separator. ; can be any non-alphanumeric
# character.
# %ACL The ACL name
# %DATA The ACL arguments. If not used then any arguments
# is automatically added at the end
#
# In addition to the above, any string specified in the referencing
# acl will also be included in the helper request line, after the
# specified formats (see the "acl external" directive)
#
# The helper receives lines per the above format specification,
# and returns lines starting with OK or ERR indicating the validity
# of the request and optionally followed by additional keywords with
# more details.
#
# General result syntax:
#
# OK/ERR keyword=value ...
#
# Defined keywords:
#
# user= The users name (login also understood)
# password= The users password (for PROXYPASS login= cache_peer)
# message= Error message or similar used as %o in error messages
# (error also understood)
# log= String to be logged in access.log. Available as
# %ea in logformat specifications
#
# If protocol=3.0 (the default) then URL escaping is used to protect
# each value in both requests and responses.
#
# If using protocol=2.5 then all values need to be enclosed in quotes
# if they may contain whitespace, or the whitespace escaped using \.
# And quotes or \ characters within the keyword value must be \ escaped.
#
# When using the concurrency= option the protocol is changed by
# introducing a query channel tag infront of the request/response.
# The query channel tag is a number between 0 and concurrency-1.
#
# Compatibility Note: The children= option was named concurrency= in
# Squid-2.5.STABLE3 and earlier, and was accepted as an alias for the
# duration of the Squid-2.5 releases to keep compatibility. However,
# the meaning of concurrency= option has changed in Squid-2.6 to match
# that of Squid-3 and the old syntax no longer works.
#
#Default:
# none
# TAG: acl
# Defining an Access List
#
# acl aclname acltype string1 ...
# acl aclname acltype "file" ...
#
# when using "file", the file should contain one item per line
#
# acltype is one of the types described below
#
# By default, regular expressions are CASE-SENSITIVE. To make
# them case-insensitive, use the -i option.
#
# acl aclname src ip-address/netmask ... (clients IP address)
# acl aclname src addr1-addr2/netmask ... (range of addresses)
# acl aclname dst ip-address/netmask ... (URL host's IP address)
# acl aclname myip ip-address/netmask ... (local socket IP address)
#
# acl aclname arp mac-address ... (xx:xx:xx:xx:xx:xx notation)
# # The arp ACL requires the special configure option --enable-arp-acl.
# # Furthermore, the arp ACL code is not portable to all operating systems.
# # It works on Linux, Solaris, FreeBSD and some other *BSD variants.
# #
# # NOTE: Squid can only determine the MAC address for clients that are on
# # the same subnet. If the client is on a different subnet, then Squid cannot
# # find out its MAC address.
#
# acl aclname srcdomain .foo.com ... # reverse lookup, client IP
# acl aclname dstdomain .foo.com ... # Destination server from URL
# acl aclname srcdom_regex [-i] xxx ... # regex matching client name
# acl aclname dstdom_regex [-i] xxx ... # regex matching server
# # For dstdomain and dstdom_regex a reverse lookup is tried if a IP
# # based URL is used and no match is found. The name "none" is used
# # if the reverse lookup fails.
#
# acl aclname time [day-abbrevs] [h1:m1-h2:m2]
# day-abbrevs:
# S - Sunday
# M - Monday
# T - Tuesday
# W - Wednesday
# H - Thursday
# F - Friday
# A - Saturday
# h1:m1 must be less than h2:m2
# acl aclname url_regex [-i] ^http:// ... # regex matching on whole URL
# acl aclname urlpath_regex [-i] \.gif$ ... # regex matching on URL path
# acl aclname urllogin [-i] [^a-zA-Z0-9] ... # regex matching on URL login field
# acl aclname port 80 70 21 ...
# acl aclname port 0-1024 ... # ranges allowed
# acl aclname myport 3128 ... # (local socket TCP port)
# acl aclname proto HTTP FTP ...
# acl aclname method GET POST ...
# acl aclname browser [-i] regexp ...
# # pattern match on User-Agent header (see also req_header below)
# acl aclname referer_regex [-i] regexp ...
# # pattern match on Referer header
# # Referer is highly unreliable, so use with care
# acl aclname ident username ...
# acl aclname ident_regex [-i] pattern ...
# # string match on ident output.
# # use REQUIRED to accept any non-null ident.
# acl aclname src_as number ...
# acl aclname dst_as number ...
# # Except for access control, AS numbers can be used for
# # routing of requests to specific caches. Here's an
# # example for routing all requests for AS#1241 and only
# # those to mycache.mydomain.net:
# # acl asexample dst_as 1241
# # cache_peer_access mycache.mydomain.net allow asexample
# # cache_peer_access mycache_mydomain.net deny all
#
# acl aclname proxy_auth [-i] username ...
# acl aclname proxy_auth_regex [-i] pattern ...
# # list of valid usernames
# # use REQUIRED to accept any valid username.
# #
# # NOTE: when a Proxy-Authentication header is sent but it is not
# # needed during ACL checking the username is NOT logged
# # in access.log.
# #
# # NOTE: proxy_auth requires a EXTERNAL authentication program
# # to check username/password combinations (see
# # auth_param directive).
# #
# # NOTE: proxy_auth can't be used in a transparent proxy as
# # the browser needs to be configured for using a proxy in order
# # to respond to proxy authentication.
#
# acl aclname snmp_community string ...
# # A community string to limit access to your SNMP Agent
# # Example:
# #
# # acl snmppublic snmp_community public
#
visible_hostname squid
# acl aclname maxconn number
# # This will be matched when the client's IP address has
# # more than <number> HTTP connections established.
#
# acl aclname max_user_ip [-s] number
# # This will be matched when the user attempts to log in from more
# # than <number> different ip addresses. The authenticate_ip_ttl
# # parameter controls the timeout on the ip entries.
# # If -s is specified the limit is strict, denying browsing
# # from any further IP addresses until the ttl has expired. Without
# # -s Squid will just annoy the user by "randomly" denying requests.
# # (the counter is reset each time the limit is reached and a
# # request is denied)
# # NOTE: in acceleration mode or where there is mesh of child proxies,
# # clients may appear to come from multiple addresses if they are
# # going through proxy farms, so a limit of 1 may cause user problems.
#
# acl aclname req_mime_type mime-type1 ...
# # regex match against the mime type of the request generated
# # by the client. Can be used to detect file upload or some
# # types HTTP tunneling requests.
# # NOTE: This does NOT match the reply. You cannot use this
# # to match the returned file type.
#
# acl aclname req_header header-name [-i] any\.regex\.here
# # regex match against any of the known request headers. May be
# # thought of as a superset of "browser", "referer" and "mime-type"
# # ACLs.
#
# acl aclname rep_mime_type mime-type1 ...
# # regex match against the mime type of the reply received by
# # squid. Can be used to detect file download or some
# # types HTTP tunneling requests.
# # NOTE: This has no effect in http_access rules. It only has
# # effect in rules that affect the reply data stream such as
# # http_reply_access.
#
# acl aclname rep_header header-name [-i] any\.regex\.here
# # regex match against any of the known reply headers. May be
# # thought of as a superset of "browser", "referer" and "mime-type"
# # ACLs.
# #
# # Example:
# #
# # acl many_spaces rep_header Content-Disposition -i [[:space:]]{3,}
#
# acl acl_name external class_name [arguments...]
# # external ACL lookup via a helper class defined by the
# # external_acl_type directive.
#
# acl urlgroup group1 ...
# # match against the urlgroup as indicated by redirectors
#
# acl aclname user_cert attribute values...
# # match against attributes in a user SSL certificate
# # attribute is one of DN/C/O/CN/L/ST
#
# acl aclname ca_cert attribute values...
# # match against attributes a users issuing CA SSL certificate
# # attribute is one of DN/C/O/CN/L/ST
#
# acl aclname ext_user username ...
# acl aclname ext_user_regex [-i] pattern ...
# # string match on username returned by external acl helper
# # use REQUIRED to accept any non-null user name.
#
#Examples:
#acl macaddress arp 09:00:2b:23:45:67
#acl myexample dst_as 1241
#acl password proxy_auth REQUIRED
#acl fileupload req_mime_type -i ^multipart/form-data$
#acl javascript rep_mime_type -i ^application/x-javascript$
#
#Recommended minimum configuration:
acl all src 0.0.0.0/0.0.0.0
acl manager proto cache_object
acl localhost src 127.0.0.1/255.255.255.255
acl to_localhost dst 127.0.0.0/8
acl SSL_ports port 443
acl Safe_ports port 80 # http
acl Safe_ports port 21 # ftp
acl Safe_ports port 443 # https
acl Safe_ports port 70 # gopher
acl Safe_ports port 210 # wais
acl Safe_ports port 1025-65535 # unregistered ports
acl Safe_ports port 280 # http-mgmt
acl Safe_ports port 488 # gss-http
acl Safe_ports port 591 # filemaker
acl Safe_ports port 777 # multiling http
acl CONNECT method CONNECT
# Novas regras
acl localhost src 10.10.200.0/255.255.255.0
acl lista url_regex "/etc/squid/lista"
# TAG: http_access
# Allowing or Denying access based on defined access lists
#
# Access to the HTTP port:
# http_access allow|deny [!]aclname ...
#
# NOTE on default values:
#
# If there are no "access" lines present, the default is to deny
# the request.
#
# If none of the "access" lines cause a match, the default is the
# opposite of the last line in the list. If the last line was
# deny, the default is allow. Conversely, if the last line
# is allow, the default will be deny. For these reasons, it is a
# good idea to have an "deny all" or "allow all" entry at the end
# of your access lists to avoid potential confusion.
#
#Default:
# http_access deny all
#
#Recommended minimum configuration:
#
# Only allow cachemgr access from localhost
http_access deny lista
http_access allow manager localhost
http_access deny manager
# Deny requests to unknown ports
http_access deny !Safe_ports
# Deny CONNECT to other than SSL ports
http_access deny CONNECT !SSL_ports
#
# We strongly recommend the following be uncommented to protect innocent
# web applications running on the proxy server who think the only
# one who can access services on "localhost" is a local user
#http_access deny to_localhost
#
# INSERT YOUR OWN RULE(S) HERE TO ALLOW ACCESS FROM YOUR CLIENTS
# Example rule allowing access from your local networks. Adapt
# to list your (internal) IP networks from where browsing should
# be allowed
#acl our_networks src 192.168.1.0/24 192.168.2.0/24
#http_access allow our_networks
# And finally deny all other access to this proxy
http_access allow localhost
http_access deny all
# TAG: http_access2
# Allowing or Denying access based on defined access lists
#
# Identical to http_access, but runs after redirectors. If not set
# then only http_access is used.
#
#Default:
# none
# TAG: http_reply_access
# Allow replies to client requests. This is complementary to http_access.
#
# http_reply_access allow|deny [!] aclname ...
#
# NOTE: if there are no access lines present, the default is to allow
# all replies
#
# If none of the access lines cause a match the opposite of the
# last line will apply. Thus it is good practice to end the rules
# with an "allow all" or "deny all" entry.
#
#Default:
# http_reply_access allow all
# TAG: icp_access
# Allowing or Denying access to the ICP port based on defined
# access lists
#
# icp_access allow|deny [!]aclname ...
#
# See http_access for details
#
#Default:
# icp_access deny all
#
#Allow ICP queries from everyone
icp_access allow all
# TAG: htcp_access
# Note: This option is only available if Squid is rebuilt with the
# --enable-htcp option
#
# Allowing or Denying access to the HTCP port based on defined
# access lists
#
# htcp_access allow|deny [!]aclname ...
#
# See http_access for details
#
# NOTE: The default if no htcp_access lines are present is to
# deny all traffic. This default may cause problems with peers
# using the htcp or htcp-oldsquid options.
#
##Allow HTCP queries from everyone
#htcp_access allow all
#
#Default:
# htcp_access deny all
# TAG: htcp_clr_access
# Note: This option is only available if Squid is rebuilt with the
# --enable-htcp option
#
# Allowing or Denying access to purge content using HTCP based
# on defined access lists
#
# htcp_clr_access allow|deny [!]aclname ...
#
# See http_access for details
#
##Allow HTCP CLR requests from trusted peers
#acl htcp_clr_peer src 172.16.1.2
#htcp_clr_access allow htcp_clr_peer
#
#Default:
# htcp_clr_access deny all
# TAG: miss_access
# Use to force your neighbors to use you as a sibling instead of
# a parent. For example:
#
# acl localclients src 172.16.0.0/16
# miss_access allow localclients
# miss_access deny !localclients
#
# This means only your local clients are allowed to fetch
# MISSES and all other clients can only fetch HITS.
#
# By default, allow all clients who passed the http_access rules
# to fetch MISSES from us.
#
#Default setting:
# miss_access allow all
# TAG: ident_lookup_access
# A list of ACL elements which, if matched, cause an ident
# (RFC931) lookup to be performed for this request. For
# example, you might choose to always perform ident lookups
# for your main multi-user Unix boxes, but not for your Macs
# and PCs. By default, ident lookups are not performed for
# any requests.
#
# To enable ident lookups for specific client addresses, you
# can follow this example:
#
# acl ident_aware_hosts src 198.168.1.0/255.255.255.0
# ident_lookup_access allow ident_aware_hosts
# ident_lookup_access deny all
#
# Only src type ACL checks are fully supported. A src_domain
# ACL might work at times, but it will not always provide
# the correct result.
#
#Default:
# ident_lookup_access deny all
# TAG: reply_body_max_size bytes allow|deny acl acl...
# This option specifies the maximum size of a reply body in bytes.
# It can be used to prevent users from downloading very large files,
# such as MP3's and movies. When the reply headers are received,
# the reply_body_max_size lines are processed, and the first line with
# a result of "allow" is used as the maximum body size for this reply.
# This size is checked twice. First when we get the reply headers,
# we check the content-length value. If the content length value exists
# and is larger than the allowed size, the request is denied and the
# user receives an error message that says "the request or reply
# is too large." If there is no content-length, and the reply
# size exceeds this limit, the client's connection is just closed
# and they will receive a partial reply.
#
# WARNING: downstream caches probably can not detect a partial reply
# if there is no content-length header, so they will cache
# partial responses and give them out as hits. You should NOT
# use this option if you have downstream caches.
#
# If you set this parameter to zero (the default), there will be
# no limit imposed.
#
#Default:
# reply_body_max_size 0 allow all
# OPTIONS FOR X-Forwarded-For
# -----------------------------------------------------------------------------
# TAG: follow_x_forwarded_for
# Allowing or Denying the X-Forwarded-For header to be followed to
# find the original source of a request.
#
# Requests may pass through a chain of several other proxies
# before reaching us. The X-Forwarded-For header will contain a
# comma-separated list of the IP addresses in the chain, with the
# rightmost address being the most recent.
#
# If a request reaches us from a source that is allowed by this
# configuration item, then we consult the X-Forwarded-For header
# to see where that host received the request from. If the
# X-Forwarded-For header contains multiple addresses, and if
# acl_uses_indirect_client is on, then we continue backtracking
# until we reach an address for which we are not allowed to
# follow the X-Forwarded-For header, or until we reach the first
# address in the list. (If acl_uses_indirect_client is off, then
# it's impossible to backtrack through more than one level of
# X-Forwarded-For addresses.)
#
# The end result of this process is an IP address that we will
# refer to as the indirect client address. This address may
# be treated as the client address for access control, delay
# pools and logging, depending on the acl_uses_indirect_client,
# delay_pool_uses_indirect_client and log_uses_indirect_client
# options.
#
# SECURITY CONSIDERATIONS:
#
# Any host for which we follow the X-Forwarded-For header
# can place incorrect information in the header, and Squid
# will use the incorrect information as if it were the
# source address of the request. This may enable remote
# hosts to bypass any access control restrictions that are
# based on the client's source addresses.
#
# For example:
#
# acl localhost src 127.0.0.1
# acl my_other_proxy srcdomain .proxy.example.com
# follow_x_forwarded_for allow localhost
# follow_x_forwarded_for allow my_other_proxy
#
#Default:
# follow_x_forwarded_for deny all
# TAG: acl_uses_indirect_client on|off
# Controls whether the indirect client address
# (see follow_x_forwarded_for) is used instead of the
# direct client address in acl matching.
#
#Default:
# acl_uses_indirect_client on
# TAG: delay_pool_uses_indirect_client on|off
# Controls whether the indirect client address
# (see follow_x_forwarded_for) is used instead of the
# direct client address in delay pools.
#
#Default:
# delay_pool_uses_indirect_client on
# TAG: log_uses_indirect_client on|off
# Controls whether the indirect client address
# (see follow_x_forwarded_for) is used instead of the
# direct client address in the access log.
#
#Default:
# log_uses_indirect_client on
# NETWORK OPTIONS
# -----------------------------------------------------------------------------
# TAG: http_port
# Usage: port [options]
# hostname:port [options]
# 1.2.3.4:port [options]
#
# The socket addresses where Squid will listen for HTTP client
# requests. You may specify multiple socket addresses.
# There are three forms: port alone, hostname with port, and
# IP address with port. If you specify a hostname or IP
# address, Squid binds the socket to that specific
# address. This replaces the old 'tcp_incoming_address'
# option. Most likely, you do not need to bind to a specific
# address, so you can use the port number alone.
#
# If you are running Squid in accelerator mode, you
# probably want to listen on port 80 also, or instead.
#
# You may specify multiple socket addresses on multiple lines.
#
# Options:
#
# transparent Support for transparent interception of
# outgoing requests without browser settings.
#
# tproxy Support Linux TPROXY for spoofing outgoing
# connections using the client IP address.
#
# accel Accelerator mode. Also needs at least one
# of vhost/vport/defaultsite.
#
# defaultsite=domainname
# What to use for the Host: header if it is not present
# in a request. Determines what site (not origin server)
# accelerators should consider the default.
# Implies accel.
#
# vhost Accelerator mode using Host header for virtual
# domain support. Implies accel.
#
# vport Accelerator with IP based virtual host support.
# Implies accel.
#
# vport=NN As above, but uses specified port number rather
# than the http_port number. Implies accel.
#
# urlgroup= Default urlgroup to mark requests with (see
# also acl urlgroup and url_rewrite_program)
#
# protocol= Protocol to reconstruct accelerated requests with.
# Defaults to http.
#
# no-connection-auth
# Prevent forwarding of Microsoft connection oriented
# authentication (NTLM, Negotiate and Kerberos)
#
# If you run Squid on a dual-homed machine with an internal
# and an external interface we recommend you to specify the
# internal address:port in http_port. This way Squid will only be
# visible on the internal address.
#
# Squid normally listens to port 3128
http_port 3128
# TAG: https_port
# Usage: [ip:]port cert=certificate.pem [key=key.pem] [options...]
#
# The socket address where Squid will listen for HTTPS client
# requests.
#
# This is really only useful for situations where you are running
# squid in accelerator mode and you want to do the SSL work at the
# accelerator level.
#
# You may specify multiple socket addresses on multiple lines,
# each with their own SSL certificate and/or options.
#
# Options:
#
# accel Accelerator mode. Also needs at least one of
# defaultsite or vhost.
#
# defaultsite= The name of the https site presented on
# this port. Implies accel.
#
# vhost Accelerator mode using Host header for virtual
# domain support. Requires a wildcard certificate
# or other certificate valid for more than one domain.
# Implies accel.
#
# urlgroup= Default urlgroup to mark requests with (see
# also acl urlgroup and url_rewrite_program).
#
# protocol= Protocol to reconstruct accelerated requests with.
# Defaults to https.
#
# cert= Path to SSL certificate (PEM format).
#
# key= Path to SSL private key file (PEM format)
# if not specified, the certificate file is
# assumed to be a combined certificate and
# key file.
#
# version= The version of SSL/TLS supported
# 1 automatic (default)
# 2 SSLv2 only
# 3 SSLv3 only
# 4 TLSv1 only
#
# cipher= Colon separated list of supported ciphers.
#
# options= Various SSL engine options. The most important
# being:
# NO_SSLv2 Disallow the use of SSLv2
# NO_SSLv3 Disallow the use of SSLv3
# NO_TLSv1 Disallow the use of TLSv1
# SINGLE_DH_USE Always create a new key when using
# temporary/ephemeral DH key exchanges
# See src/ssl_support.c or OpenSSL SSL_CTX_set_options
# documentation for a complete list of options.
#
# clientca= File containing the list of CAs to use when
# requesting a client certificate.
#
# cafile= File containing additional CA certificates to
# use when verifying client certificates. If unset
# clientca will be used.
#
# capath= Directory containing additional CA certificates
# and CRL lists to use when verifying client certificates.
#
# crlfile= File of additional CRL lists to use when verifying
# the client certificate, in addition to CRLs stored in
# the capath. Implies VERIFY_CRL flag below.
#
# dhparams= File containing DH parameters for temporary/ephemeral
# DH key exchanges.
#
# sslflags= Various flags modifying the use of SSL:
# DELAYED_AUTH
# Don't request client certificates
# immediately, but wait until acl processing
# requires a certificate (not yet implemented).
# NO_DEFAULT_CA
# Don't use the default CA lists built in
# to OpenSSL.
# NO_SESSION_REUSE
# Don't allow for session reuse. Each connection
# will result in a new SSL session.
# VERIFY_CRL
# Verify CRL lists when accepting client
# certificates.
# VERIFY_CRL_ALL
# Verify CRL lists for all certificates in the
# client certificate chain.
#
# sslcontext= SSL session ID context identifier.
#
# vport Accelerator with IP based virtual host support.
#
# vport=NN As above, but uses specified port number rather
# than the https_port number. Implies accel.
#
#
#Default:
# none
# TAG: tcp_outgoing_tos
# Allows you to select a TOS/Diffserv value to mark outgoing
# connections with, based on the username or source address
# making the request.
#
# tcp_outgoing_tos ds-field [!]aclname ...
#
# Example where normal_service_net uses the TOS value 0x00
# and good_service_net uses 0x20
#
# acl normal_service_net src 10.0.0.0/255.255.255.0
# acl good_service_net src 10.0.1.0/255.255.255.0
# tcp_outgoing_tos 0x00 normal_service_net
# tcp_outgoing_tos 0x20 good_service_net
#
# TOS/DSCP values really only have local significance - so you should
# know what you're specifying. For more information, see RFC2474 and
# RFC3260.
#
# The TOS/DSCP byte must be exactly that - a octet value 0 - 255, or
# "default" to use whatever default your host has. Note that in
# practice often only values 0 - 63 is usable as the two highest bits
# have been redefined for use by ECN (RFC3168).
#
# Processing proceeds in the order specified, and stops at first fully
# matching line.
#
# Note: The use of this directive using client dependent ACLs is
# incompatible with the use of server side persistent connections. To
# ensure correct results it is best to set server_persisten_connections
# to off when using this directive in such configurations.
#
#Default:
# none
# TAG: tcp_outgoing_address
# Allows you to map requests to different outgoing IP addresses
# based on the username or source address of the user making
# the request.
#
# tcp_outgoing_address ipaddr [[!]aclname] ...
#
# Example where requests from 10.0.0.0/24 will be forwarded
# with source address 10.1.0.1, 10.0.2.0/24 forwarded with
# source address 10.1.0.2 and the rest will be forwarded with
# source address 10.1.0.3.
#
# acl normal_service_net src 10.0.0.0/24
# acl good_service_net src 10.0.1.0/24 10.0.2.0/24
# tcp_outgoing_address 10.1.0.1 normal_service_net
# tcp_outgoing_address 10.1.0.2 good_service_net
# tcp_outgoing_address 10.1.0.3
#
# Processing proceeds in the order specified, and stops at first fully
# matching line.
#
# Note: The use of this directive using client dependent ACLs is
# incompatible with the use of server side persistent connections. To
# ensure correct results it is best to set server_persistent_connections
# to off when using this directive in such configurations.
#
#Default:
# none
# SSL OPTIONS
# -----------------------------------------------------------------------------
# TAG: ssl_unclean_shutdown
# Some browsers (especially MSIE) bugs out on SSL shutdown
# messages.
#
#Default:
# ssl_unclean_shutdown off
# TAG: ssl_engine
# The OpenSSL engine to use. You will need to set this if you
# would like to use hardware SSL acceleration for example.
#
#Default:
# none
# TAG: sslproxy_client_certificate
# Client SSL Certificate to use when proxying https:// URLs
#
#Default:
# none
# TAG: sslproxy_client_key
# Client SSL Key to use when proxying https:// URLs
#
#Default:
# none
# TAG: sslproxy_version
# SSL version level to use when proxying https:// URLs
#
#Default:
# sslproxy_version 1
# TAG: sslproxy_options
# SSL engine options to use when proxying https:// URLs
#
#Default:
# none
# TAG: sslproxy_cipher
# SSL cipher list to use when proxying https:// URLs
#
#Default:
# none
# TAG: sslproxy_cafile
# file containing CA certificates to use when verifying server
# certificates while proxying https:// URLs
#
#Default:
# none
# TAG: sslproxy_capath
# directory containing CA certificates to use when verifying
# server certificates while proxying https:// URLs
#
#Default:
# none
# TAG: sslproxy_flags
# Various flags modifying the use of SSL while proxying https:// URLs:
# DONT_VERIFY_PEER Accept certificates even if they fail to
# verify.
# NO_DEFAULT_CA Don't use the default CA list built in
# to OpenSSL.
#
#Default:
# none
# TAG: sslpassword_program
# Specify a program used for entering SSL key passphrases
# when using encrypted SSL certificate keys. If not specified
# keys must either be unencrypted, or Squid started with the -N
# option to allow it to query interactively for the passphrase.
#
#Default:
# none
# OPTIONS WHICH AFFECT THE NEIGHBOR SELECTION ALGORITHM
# -----------------------------------------------------------------------------
# TAG: cache_peer
# To specify other caches in a hierarchy, use the format:
#
# cache_peer hostname type http-port icp-port [options]
#
# For example,
#
# # proxy icp
# # hostname type port port options
# # -------------------- -------- ----- ----- -----------
# cache_peer parent.foo.net parent 3128 3130 proxy-only default
# cache_peer sib1.foo.net sibling 3128 3130 proxy-only
# cache_peer sib2.foo.net sibling 3128 3130 proxy-only
#
# type: either 'parent', 'sibling', or 'multicast'.
#
# proxy-port: The port number where the cache listens for proxy
# requests.
#
# icp-port: Used for querying neighbor caches about
# objects. To have a non-ICP neighbor
# specify '7' for the ICP port and make sure the
# neighbor machine has the UDP echo port
# enabled in its /etc/inetd.conf file.
# NOTE: Also requires icp_port option enabled to send/receive
# requests via this method.
#
# options: proxy-only
# weight=n
# ttl=n
# no-query
# default
# round-robin
# carp
# multicast-responder
# closest-only
# no-digest
# no-netdb-exchange
# no-delay
# login=user:password | PASS | *:password
# connect-timeout=nn
# digest-url=url
# allow-miss
# max-conn=n
# htcp
# htcp-oldsquid
# originserver
# userhash
# sourcehash
# name=xxx
# monitorurl=url
# monitorsize=sizespec
# monitorinterval=seconds
# monitortimeout=seconds
# forceddomain=name
# ssl
# sslcert=/path/to/ssl/certificate
# sslkey=/path/to/ssl/key
# sslversion=1|2|3|4
# sslcipher=...
# ssloptions=...
# front-end-https[=on|auto]
# connection-auth[=on|off|auto]
#
# use 'proxy-only' to specify objects fetched
# from this cache should not be saved locally.
#
# use 'weight=n' to affect the selection of a peer
# during any weighted peer-selection mechanisms.
# The weight must be an integer; default is 1,
# larger weights are favored more.
# This option does not affect parent selection if a peering
# protocol is not in use.
#
# use 'ttl=n' to specify a IP multicast TTL to use
# when sending an ICP queries to this address.
# Only useful when sending to a multicast group.
# Because we don't accept ICP replies from random
# hosts, you must configure other group members as
# peers with the 'multicast-responder' option below.
#
# use 'no-query' to NOT send ICP queries to this
# neighbor.
#
# use 'default' if this is a parent cache which can
# be used as a "last-resort" if a peer cannot be located
# by any of the peer-selection mechanisms.
# If specified more than once, only the first is used.
#
# use 'round-robin' to define a set of parents which
# should be used in a round-robin fashion in the
# absence of any ICP queries.
#
# use 'carp' to define a set of parents which should
# be used as a CARP array. The requests will be
# distributed among the parents based on the CARP load
# balancing hash function based on their weight.
#
# 'multicast-responder' indicates the named peer
# is a member of a multicast group. ICP queries will
# not be sent directly to the peer, but ICP replies
# will be accepted from it.
#
# 'closest-only' indicates that, for ICP_OP_MISS
# replies, we'll only forward CLOSEST_PARENT_MISSes
# and never FIRST_PARENT_MISSes.
#
# use 'no-digest' to NOT request cache digests from
# this neighbor.
#
# 'no-netdb-exchange' disables requesting ICMP
# RTT database (NetDB) from the neighbor.
#
# use 'no-delay' to prevent access to this neighbor
# from influencing the delay pools.
#
# use 'login=user:password' if this is a personal/workgroup
# proxy and your parent requires proxy authentication.
# Note: The string can include URL escapes (i.e. %20 for
# spaces). This also means % must be written as %%.
#
# use 'login=PASS' if users must authenticate against
# the upstream proxy or in the case of a reverse proxy
# configuration, the origin web server. This will pass
# the users credentials as they are to the peer.
# Note: To combine this with local authentication the Basic
# authentication scheme must be used, and both servers must
# share the same user database as HTTP only allows for
# a single login (one for proxy, one for origin server).
# Also be warned this will expose your users proxy
# password to the peer. USE WITH CAUTION
#
# use 'login=*:password' to pass the username to the
# upstream cache, but with a fixed password. This is meant
# to be used when the peer is in another administrative
# domain, but it is still needed to identify each user.
# The star can optionally be followed by some extra
# information which is added to the username. This can
# be used to identify this proxy to the peer, similar to
# the login=username:password option above.
#
# use 'connect-timeout=nn' to specify a peer
# specific connect timeout (also see the
# peer_connect_timeout directive)
#
# use 'digest-url=url' to tell Squid to fetch the cache
# digest (if digests are enabled) for this host from
# the specified URL rather than the Squid default
# location.
#
# use 'allow-miss' to disable Squid's use of only-if-cached
# when forwarding requests to siblings. This is primarily
# useful when icp_hit_stale is used by the sibling. To
# extensive use of this option may result in forwarding
# loops, and you should avoid having two-way peerings
# with this option. (for example to deny peer usage on
# requests from peer by denying cache_peer_access if the
# source is a peer)
#
# use 'max-conn=n' to limit the amount of connections Squid
# may open to this peer.
#
# use 'htcp' to send HTCP, instead of ICP, queries
# to the neighbor. You probably also want to
# set the "icp port" to 4827 instead of 3130.
# You must also allow this Squid htcp_access and
# http_access in the peer Squid configuration.
#
# use 'htcp-oldsquid' to send HTCP to old Squid versions
# You must also allow this Squid htcp_access and
# http_access in the peer Squid configuration.
#
# 'originserver' causes this parent peer to be contacted as
# a origin server. Meant to be used in accelerator setups.
#
# use 'userhash' to load-balance amongst a set of parents
# based on the client proxy_auth or ident username.
#
# use 'sourcehash' to load-balance amongst a set of parents
# based on the client source ip.
#
# use 'name=xxx' if you have multiple peers on the same
# host but different ports. This name can be used to
# differentiate the peers in cache_peer_access and similar
# directives.
#
# use 'monitorurl=url' to have periodically request a given
# URL from the peer, and only consider the peer as alive
# if this monitoring is successful (default none)
#
# use 'monitorsize=min[-max]' to limit the size range of
# 'monitorurl' replies considered valid. Defaults to 0 to
# accept any size replies as valid.
#
# use 'monitorinterval=seconds' to change frequency of
# how often the peer is monitored with 'monitorurl'
# (default 300 for a 5 minute interval). If set to 0
# then monitoring is disabled even if a URL is defined.
#
# use 'monitortimeout=seconds' to change the timeout of
# 'monitorurl'. Defaults to 'monitorinterval'.
#
# use 'forceddomain=name' to forcibly set the Host header
# of requests forwarded to this peer. Useful in accelerator
# setups where the server (peer) expects a certain domain
# name and using redirectors to feed this domain name
# is not feasible.
#
# use 'ssl' to indicate connections to this peer should
# be SSL/TLS encrypted.
#
# use 'sslcert=/path/to/ssl/certificate' to specify a client
# SSL certificate to use when connecting to this peer.
#
# use 'sslkey=/path/to/ssl/key' to specify the private SSL
# key corresponding to sslcert above. If 'sslkey' is not
# specified 'sslcert' is assumed to reference a
# combined file containing both the certificate and the key.
#
# use sslversion=1|2|3|4 to specify the SSL version to use
# when connecting to this peer
# 1 = automatic (default)
# 2 = SSL v2 only
# 3 = SSL v3 only
# 4 = TLS v1 only
#
# use sslcipher=... to specify the list of valid SSL ciphers
# to use when connecting to this peer.
#
# use ssloptions=... to specify various SSL engine options:
# NO_SSLv2 Disallow the use of SSLv2
# NO_SSLv3 Disallow the use of SSLv3
# NO_TLSv1 Disallow the use of TLSv1
# See src/ssl_support.c or the OpenSSL documentation for
# a more complete list.
#
# use sslcafile=... to specify a file containing
# additional CA certificates to use when verifying the
# peer certificate.
#
# use sslcapath=... to specify a directory containing
# additional CA certificates to use when verifying the
# peer certificate.
#
# use sslcrlfile=... to specify a certificate revocation
# list file to use when verifying the peer certificate.
#
# use sslflags=... to specify various flags modifying the
# SSL implementation:
# DONT_VERIFY_PEER
# Accept certificates even if they fail to
# verify.
# NO_DEFAULT_CA
# Don't use the default CA list built in
# to OpenSSL.
#
# use ssldomain= to specify the peer name as advertised
# in it's certificate. Used for verifying the correctness
# of the received peer certificate. If not specified the
# peer hostname will be used.
#
# use front-end-https to enable the "Front-End-Https: On"
# header needed when using Squid as a SSL frontend in front
# of Microsoft OWA. See MS KB document Q307347 for details
# on this header. If set to auto the header will
# only be added if the request is forwarded as a https://
# URL.
#
# use connection-auth=off to tell Squid that this peer does
# not support Microsoft connection oriented authentication,
# and any such challenges received from there should be
# ignored. Default is auto to automatically determine the
# status of the peer.
#
#Default:
# none
# TAG: cache_peer_domain
# Use to limit the domains for which a neighbor cache will be
# queried. Usage:
#
# cache_peer_domain cache-host domain [domain ...]
# cache_peer_domain cache-host !domain
#
# For example, specifying
#
# cache_peer_domain parent.foo.net .edu
#
# has the effect such that UDP query packets are sent to
# 'bigserver' only when the requested object exists on a
# server in the .edu domain. Prefixing the domain name
# with '!' means the cache will be queried for objects
# NOT in that domain.
#
# NOTE: * Any number of domains may be given for a cache-host,
# either on the same or separate lines.
# * When multiple domains are given for a particular
# cache-host, the first matched domain is applied.
# * Cache hosts with no domain restrictions are queried
# for all requests.
# * There are no defaults.
# * There is also a 'cache_peer_access' tag in the ACL
# section.
#
#Default:
# none
# TAG: cache_peer_access
# Similar to 'cache_peer_domain' but provides more flexibility by
# using ACL elements.
#
# cache_peer_access cache-host allow|deny [!]aclname ...
#
# The syntax is identical to 'http_access' and the other lists of
# ACL elements. See the comments for 'http_access' below, or
# the Squid FAQ (http://www.squid-cache.org/FAQ/FAQ-10.html).
#
#Default:
# none
# TAG: neighbor_type_domain
# usage: neighbor_type_domain neighbor parent|sibling domain domain ...
#
# Modifying the neighbor type for specific domains is now
# possible. You can treat some domains differently than the the
# default neighbor type specified on the 'cache_peer' line.
# Normally it should only be necessary to list domains which
# should be treated differently because the default neighbor type
# applies for hostnames which do not match domains listed here.
#
#EXAMPLE:
# cache_peer cache.foo.org parent 3128 3130
# neighbor_type_domain cache.foo.org sibling .com .net
# neighbor_type_domain cache.foo.org sibling .au .de
#
#Default:
# none
# TAG: dead_peer_timeout (seconds)
# This controls how long Squid waits to declare a peer cache
# as "dead." If there are no ICP replies received in this
# amount of time, Squid will declare the peer dead and not
# expect to receive any further ICP replies. However, it
# continues to send ICP queries, and will mark the peer as
# alive upon receipt of the first subsequent ICP reply.
#
# This timeout also affects when Squid expects to receive ICP
# replies from peers. If more than 'dead_peer' seconds have
# passed since the last ICP reply was received, Squid will not
# expect to receive an ICP reply on the next query. Thus, if
# your time between requests is greater than this timeout, you
# will see a lot of requests sent DIRECT to origin servers
# instead of to your parents.
#
#Default:
# dead_peer_timeout 10 seconds
# TAG: hierarchy_stoplist
# A list of words which, if found in a URL, cause the object to
# be handled directly by this cache. In other words, use this
# to not query neighbor caches for certain objects. You may
# list this option multiple times. Note: never_direct overrides
# this option.
#We recommend you to use at least the following line.
hierarchy_stoplist cgi-bin ?
# MEMORY CACHE OPTIONS
# -----------------------------------------------------------------------------
# TAG: cache_mem (bytes)
# NOTE: THIS PARAMETER DOES NOT SPECIFY THE MAXIMUM PROCESS SIZE.
# IT ONLY PLACES A LIMIT ON HOW MUCH ADDITIONAL MEMORY SQUID WILL
# USE AS A MEMORY CACHE OF OBJECTS. SQUID USES MEMORY FOR OTHER
# THINGS AS WELL. SEE THE SQUID FAQ SECTION 8 FOR DETAILS.
#
# 'cache_mem' specifies the ideal amount of memory to be used
# for:
# * In-Transit objects
# * Hot Objects
# * Negative-Cached objects
#
# Data for these objects are stored in 4 KB blocks. This
# parameter specifies the ideal upper limit on the total size of
# 4 KB blocks allocated. In-Transit objects take the highest
# priority.
#
# In-transit objects have priority over the others. When
# additional space is needed for incoming data, negative-cached
# and hot objects will be released. In other words, the
# negative-cached and hot objects will fill up any unused space
# not needed for in-transit objects.
#
# If circumstances require, this limit will be exceeded.
# Specifically, if your incoming request rate requires more than
# 'cache_mem' of memory to hold in-transit objects, Squid will
# exceed this limit to satisfy the new requests. When the load
# decreases, blocks will be freed until the high-water mark is
# reached. Thereafter, blocks will be used to store hot
# objects.
#
#Default:
#cache_mem 8 MB
# TAG: maximum_object_size_in_memory (bytes)
# Objects greater than this size will not be attempted to kept in
# the memory cache. This should be set high enough to keep objects
# accessed frequently in memory to improve performance whilst low
# enough to keep larger objects from hoarding cache_mem.
#
#Default:
# maximum_object_size_in_memory 8 KB
# TAG: memory_replacement_policy
# The memory replacement policy parameter determines which
# objects are purged from memory when memory space is needed.
#
# See cache_replacement_policy for details.
#
#Default:
# memory_replacement_policy lru
# DISK CACHE OPTIONS
# -----------------------------------------------------------------------------
# TAG: cache_replacement_policy
# The cache replacement policy parameter determines which
# objects are evicted (replaced) when disk space is needed.
#
# lru : Squid's original list based LRU policy
# heap GDSF : Greedy-Dual Size Frequency
# heap LFUDA: Least Frequently Used with Dynamic Aging
# heap LRU : LRU policy implemented using a heap
#
# Applies to any cache_dir lines listed below this.
#
# The LRU policies keeps recently referenced objects.
#
# The heap GDSF policy optimizes object hit rate by keeping smaller
# popular objects in cache so it has a better chance of getting a
# hit. It achieves a lower byte hit rate than LFUDA though since
# it evicts larger (possibly popular) objects.
#
# The heap LFUDA policy keeps popular objects in cache regardless of
# their size and thus optimizes byte hit rate at the expense of
# hit rate since one large, popular object will prevent many
# smaller, slightly less popular objects from being cached.
#
# Both policies utilize a dynamic aging mechanism that prevents
# cache pollution that can otherwise occur with frequency-based
# replacement policies.
#
# NOTE: if using the LFUDA replacement policy you should increase
# the value of maximum_object_size above its default of 4096 KB to
# to maximize the potential byte hit rate improvement of LFUDA.
#
# For more information about the GDSF and LFUDA cache replacement
# policies see
http://www.hpl.hp.com/techreports/1999/HPL-1999-69.html
# and
http://fog.hpl.external.hp.com/techreports/98/HPL-98-173.html.
#
#Default:
# cache_replacement_policy lru
# TAG: cache_dir
# Usage:
#
# cache_dir Type Directory-Name Fs-specific-data [options]
#
# You can specify multiple cache_dir lines to spread the
# cache among different disk partitions.
#
# Type specifies the kind of storage system to use. Only "ufs"
# is built by default. To enable any of the other storage systems
# see the --enable-storeio configure option.
#
# 'Directory' is a top-level directory where cache swap
# files will be stored. If you want to use an entire disk
# for caching, this can be the mount-point directory.
# The directory must exist and be writable by the Squid
# process. Squid will NOT create this directory for you.
# Only using COSS, a raw disk device or a stripe file can
# be specified, but the configuration of the "cache_swap_log"
# tag is mandatory.
#
# The ufs store type:
#
# "ufs" is the old well-known Squid storage format that has always
# been there.
#
# cache_dir ufs Directory-Name Mbytes L1 L2 [options]
#
# 'Mbytes' is the amount of disk space (MB) to use under this
# directory. The default is 100 MB. Change this to suit your
# configuration. Do NOT put the size of your disk drive here.
# Instead, if you want Squid to use the entire disk drive,
# subtract 20% and use that value.
#
# 'Level-1' is the number of first-level subdirectories which
# will be created under the 'Directory'. The default is 16.
#
# 'Level-2' is the number of second-level subdirectories which
# will be created under each first-level directory. The default
# is 256.
#
# The aufs store type:
#
# "aufs" uses the same storage format as "ufs", utilizing
# POSIX-threads to avoid blocking the main Squid process on
# disk-I/O. This was formerly known in Squid as async-io.
#
# cache_dir aufs Directory-Name Mbytes L1 L2 [options]
#
# see argument descriptions under ufs above
#
# The diskd store type:
#
# "diskd" uses the same storage format as "ufs", utilizing a
# separate process to avoid blocking the main Squid process on
# disk-I/O.
#
# cache_dir diskd Directory-Name Mbytes L1 L2 [options] [Q1=n] [Q2=n]
#
# see argument descriptions under ufs above
#
# Q1 specifies the number of unacknowledged I/O requests when Squid
# stops opening new files. If this many messages are in the queues,
# Squid won't open new files. Default is 64
#
# Q2 specifies the number of unacknowledged messages when Squid
# starts blocking. If this many messages are in the queues,
# Squid blocks until it receives some replies. Default is 72
#
# When Q1 < Q2 (the default), the cache directory is optimized
# for lower response time at the expense of a decrease in hit
# ratio. If Q1 > Q2, the cache directory is optimized for
# higher hit ratio at the expense of an increase in response
# time.
#
# The coss store type:
#
# block-size=n defines the "block size" for COSS cache_dir's.
# Squid uses file numbers as block numbers. Since file numbers
# are limited to 24 bits, the block size determines the maximum
# size of the COSS partition. The default is 512 bytes, which
# leads to a maximum cache_dir size of 512<<24, or 8 GB. Note
# you should not change the COSS block size after Squid
# has written some objects to the cache_dir.
#
# ove
