Placa de Rede Não entra Em Modo Monitoramento! parrot S. linux

Ola queria saber como resolver meu problema
Minha placa de rede Nao entra em modo de monitoramento

Meu notbook e um CCE WIN de 32bites eu usso O Sistema Operacional
>>>>>PARROT SECURITY OS<<<<

OBS/ meu pc esta em dual boot win8 e parrot security


Quando eu digito (ifconfig) retorna assim >>

eth0 Link encap:Ethernet Endereço de HW 00:e0:4c:4c:53:76
UP BROADCASTMULTICAST MTU:1500 Métrica:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
colisões:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

lo Link encap:Loopback Local
inet end.: 127.0.0.1 Masc:255.0.0.0
endereço inet6: ::1/128 Escopo:Máquina
UP LOOPBACKRUNNING MTU:65536 Métrica:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
colisões:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

wlan0 Link encap:Ethernet Endereço de HW e0:91:53:35:97:34
UP BROADCASTMULTICAST MTU:1500 Métrica:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
colisões:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)



---E quando eu digito para ela ficar em modo de monitoramneto (airmon-ng start wlan0) retorna isso >>


Found 2 processes that could cause trouble.
If airodump-ng, aireplay-ng or airtun-ng stops working after
a short period of time, you may want to kill (some of) them!

PID Name
742 NetworkManager
917 wpa_supplicant

PHY Interface Driver Chipset

phy0 wlan0 rtl8192se Realtek Semiconductor Co., Ltd. RTL8191SEvB (rev 10)

Newly created monitor mode interface wlan0mon is *NOT* in monitor mode.
Removing non-monitor wlan0mon interface...

WARNING: unable to start monitor mode, please run "airmon-ng check kill"








``AQUI UMA SAIDA DO COMANDO ``LSPCI``



00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02)
00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02)
00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06)
00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05)
00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05)
00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05)
00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 05)
00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 05)
00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5)
00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05)
00:1f.2 IDE interface: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA IDE Controller (rev 05)
00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05)
00:1f.5 IDE interface: Intel Corporation 5 Series/3400 Series Chipset 2 port SATA IDE Controller (rev 05)
00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05)
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02)
06:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8191SEvB Wireless LAN Controller (rev 10)
ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02)
ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02)
ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02)
ff:02.1 Host bridge: Intel Corporation 1st Generation Core Processor QPI Physical 0 (rev 02)
ff:02.2 Host bridge: Intel Corporation 1st Generation Core Processor Reserved (rev 02)
ff:02.3 Host bridge: Intel Corporation 1st Generation Core Processor Reserved (rev 02)

Aviso estampado do sistema:
WARNING: unable to start monitor mode, please run "airmon-ng check kill"
Tradução:
AVISO: não foi possível iniciar o modo promíscuo, por favor rode o comando "airmon-ng check kill"

Se após isso ainda não conseguir iniciar talvez sua placa não possua suporte para tal. Mas somente para confirmar poste a saída deste comando:

iw phy phy0 info | grep -A8 modes 

- Já Mano, eu Coloquei O Comando ( airmon-ng check kill ) e O Wifi Desligou Sozinho E tive que reiniciar O PC !

Depois Coloquei O Outro Comando ( iw phy phy0 info | grep -A8 modes )

E Saiu Assim >>


Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
* mesh point
* P2P-client
* P2P-GO
--
software interface modes (can always be added):
* AP/VLAN
* monitor
interface combinations are not supported
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz

Suponhamos que sua placa seja wlan0......

ifconfig wlan0 down
iwconfig wlan0 mode monitor
ifconfig wlan0 up

e

iwconfig

para ver se o modo monitor foi ativado.

Antes de iniciar faça o seguinte:
# Desative o network-manager

nmcli n off 

# Destrua os processos do wpa_supplicant

killall wpa_supplicant 

# Levante a interface de rede novamente

ifconfig wlan* up 

E tente novamente.

# Restaurar o network-manager

nmcli n on 

nao funcionou mano continua o mesmo jeito, sem monitoramento

Aqui a saida do comando (airmon-ng start wlan0)



Found 2 processes that could cause trouble.
If airodump-ng, aireplay-ng or airtun-ng stops working after
a short period of time, you may want to kill (some of) them!

PID Name
735 NetworkManager
909 wpa_supplicant

PHY Interface Driver Chipset

phy0 wlan0 rtl8192se Realtek Semiconductor Co., Ltd. RTL8191SEvB (rev 10)

Newly created monitor mode interface wlan0mon is *NOT* in monitor mode.
Removing non-monitor wlan0mon interface...

WARNING: unable to start monitor mode, please run "airmon-ng check kill"



- Me Ajudem ! Obg

e quando eu coloco o comando que pedi,>>>

(airmon-ng check kill)
aparece isso>>>



Killing these processes:

PID Name
911 wpa_supplicant

Já Gente Conseguir, Fui No YouTube Procurar !

- O Link Aki
https://m.youtube.com/watch?v=FGZ94gtVLkg

Ei ? Como Que Eu Faço Pra Colocar Como RESOLVIDO o topico ??